A dip tube is a plastic pipe inside the tank that sends cold water to the bottom so the burner or element can heat it. When the tube cracks or breaks, cold water mixes with hot at the top. The signs are lukewarm water, hot water that runs out fast and small plastic bits in aerators and filters.
Replacing a dip tube is a repair many handy people can do, as long as the water and gas or power are off. If the tank is old, replacement may make more sense, and our water heater replacement page explains how to decide.
SymptomsSigns A Dip Tube Has Failed
Common clues
- Hot water turns lukewarm after a short time
- Tiny white or gray plastic bits in faucet screens
- The water heater seems to run all the time
- The tank feels hot at the top but the water at the tap is only warm
- The tank is not leaking and the thermostat looks fine
Older plastic tubes from certain years were known to break down. Newer tubes use better plastic, but heat and age still take a toll.
Quick ChecksRule Out Simpler Problems First
| Check | What it tells you |
|---|---|
| Thermostat or gas control setting | Too low a setting gives lukewarm water |
| Breaker or pilot light | No power or flame gives cold water |
| Heating element on an electric unit | A bad lower element gives lukewarm water |
| Sediment in the tank | Rumbling and reduced capacity |
| Plastic bits in aerators | Points strongly to a dip tube |
Unscrew a faucet aerator and look for small pieces. If you find plastic bits, the dip tube is a strong suspect.
ProcessThe Steps To Replace It
Shut down
Turn off power or gas and close the cold water inlet.
Drain a few gallons
Open a hot tap and drain enough to lower the water level below the inlet.
Remove the cold nipple
Disconnect the cold line and unscrew the inlet fitting. The dip tube sits inside it.
Install the new tube
Slide in the new tube, reconnect the line and fill the tank before restoring power or gas.
Open a hot tap while the tank fills so air can escape. Check the inlet fitting for leaks, then restore power or gas. Run a hot tap for a minute to flush out plastic bits so they do not clog fixtures.
Know When To StopWhen Replacing The Tube Is Not Enough
If the tank is more than ten years old, rusty at the base or leaking from the body, a new tube will not solve the bigger problem. A dip tube repair makes sense on a tank that is otherwise sound. If the tank is failing, put the money toward a new unit.
Gas units add risk. If you are unsure about handling the gas control, shut off the gas, leave the repair and call us. See water heater repair for how we diagnose tanks.
MaintenancePreventing The Next Failure
Drain a few gallons from the tank drain once a year to move sediment out. Check the anode rod on a schedule if the manufacturer calls for it. Keep the temperature setting reasonable, because very high settings stress parts and raise scald risk.
We repair and replace tanks around Lehi and in nearby towns such as American Fork. See the areas page for the full list.
After The RepairChecking The Result After The Swap
After the new dip tube is in, refill the tank completely before turning on power or lighting the burner. Open a hot tap somewhere in the house until the water runs steadily, which pushes air out of the lines. Then check the connections at the top of the tank for drips.
Give the heater a few hours to reach temperature before judging the fix. If the water is still lukewarm, the cause may be a failed thermostat, a heating element, a burner problem or heavy sediment. The tube is only one possible cause.
Flush a few gallons from the drain valve once a year to clear sediment. A tank that has never been flushed may have a valve that is stuck. Call us if it will not open, because forcing it can cause a leak.
Rule It OutOther Causes Of Lukewarm Water
Lukewarm water also comes from a thermostat set too low, an undersized heater or crossed connections at a mixing valve or single handle faucet. Check the thermostat setting and try another faucet first. That tells you whether the problem is the heater or one fixture.
Questions about your own house? Call (385) 488-1892 and a person will answer.
FAQsDip Tube Questions
Lukewarm water, hot water that runs out quickly and plastic bits in aerators are the strongest signs.
Many people finish in an hour or two once the tank has drained enough and the new tube is on hand.
It can be done, but you must shut off gas and verify the burner is out before working. If you are not sure, call a plumber.
If the tank is old or leaking, yes. If the tank is sound, a new tube is a low cost fix.
Broken pieces of a dip tube travel with the hot water. Clean the aerators after the repair.

